How To Move Leather Bar Wraps from Handlebar to Handlebar

Unlike most bar tape, you can re-stitch and re-wrap our “zero waste” veg-tan leather bar wraps for years to come.

Last year I bought a set of your sew on bar wraps, but now I want to switch brake levers. Can I “un-sew” the leather up to the brake clamp and get them “re-sewn” without destroying the leather?

– Mike W.

There are many reasons why one might want to un-install and re-install leather wraps: bicycle maintenance, switch out the handlebars or change bikes.

Keep the Leather Patina You’ve Earned

Unlike typical bar tapes, vegetable-tanned leather bar wraps earn a beautiful patina from the oils and sweats in your hands over miles over riding and actually improve with time and use. And you can keep that well-earned patina: our vegetable-tanned leather will last you a lifetime and can be removed and re-installed many times over.

Bicycle bar wraps don’t have to be a disposable, one-time-use product. Most bar tapes are made out of limited lifetime materials, like plasticky foam, bonded leather composite, or cork composite that disintegrate and look dirty with time and use.

Our master craftsman and fellow bicycle commuter Geoff Franklin was actually first inspired to make these leather bar wraps when he was poring over modern-day pictures of vintage European bicycles. In the images, he noticed all the leather accents that must have been nearly 100 years old still looked gorgeous — in some cases, in better shape than the bicycle itself!

How to Un-install and Re-install Leather Bar Wraps

These re-installation instructions apply to all of our vegetable-tanned leather handlebar wrap styles and the Portage Strap, a stitched-on leather shoulder cushion for the bicycle frame. Geoff has personally moved the same set of Sew-on Bar Wraps onto three different bars over a ten-year period.

The same instructions apply for non-traditional uses of our leather bar wraps too, such as for gym equipment, strollers, appliances, tool handles, or architectural applications.

Before You Get Started

To Un-install Wraps

  • For stitched products, take thread nippers or an exacto blade, and cut the thread between the two edges of leather down the length of the bars.
  • Cut or unravel the thread or tape anchoring the ends, being careful not to cut the leather itself.
  • Un-do the coil, braid, or stitching and remove.

To Re-install Wraps

  • When you’re ready to re-install them, follow the same directions exactly like last time.
  • Be sure to clean the bars again and re-wet the leather.

Tips and Tricks

  • Getting the leather wet makes it pliable and forgiving. Use room temperature water. You can’t get them too wet.
  • Be aware of cutting wraps short — if you cut them short every time you re-install, there will be less and less available for future re-wraps.
  • Be aware of the possibility of shrinkage, particularly when wraps are wet. Wait until fully dry before trimming to length. Read more about tackling shrinkage.
  • When re-installing braided wraps, like the Bullwhip Braided Bar Wraps, bear in mind that the new braid will most likely be slightly different than the last. It’s near-impossible to braid exactly the same way, which may disrupt the look of the patina. Don’t worry: you’ll give it an ever better patina with more miles in the saddle.
  • If you’re changing to a shorter handlebar, such as from a drop bar to a bullhorn, you can cut the leather short using sharp scissors or an exacto blade. If it’s a stitched-on product like the Sew-on Bar Wraps or City Grips, Geoff recommends measuring carefully (“measure twice, cut once!”) before cutting to try to avoid cutting midway through a stitch hole.

How did your re-installation go? We’d love to hear your thoughts and experiences!

City Grips Installation series by customer Tim Kau, circa 2012


About Walnut Studiolo’s Leather Bicycle Accessories

  • Our handcrafted leather bicycle accessories are the finest on the market.
  • As cyclists ourselves, we create completely original designs and make them ourselves in our Oregon workshop.
  • Often imitated but never equaled, we take no shortcuts in our production: every product we make is built to last, and made the “longhand” way.
  • We have a strong commitment to sustainability in both our products and operations.
  • Repairability is the new luxury.” Our unique hand-dyed American leather gets better with age, offering a warm and comfortable touch with strong, long-lasting durability.
  • Award-Winning Designs: We’ve been honored national and internationally by renowned design arbiters and museums, including the Museum of Modern Art NYC (MoMA), Kickstarter, German Design Council, and more.

About Walnut Studiolo

Walnut Studiolo crafts original modern designs by hand in our Oregon workshop using only natural materials. We are a family-run company located on the North Oregon Coast. Learn more about us on our website: https://walnutstudiolo.com

Subscribe to our newsletter for more posts like this one, a monthly workshop newsletter, and 10% off your first order. Be the first to learn about our popular annual friends-and-family “AS-IS” sale.

Processing…
Success! You're on the list.

One thought on “How To Move Leather Bar Wraps from Handlebar to Handlebar

Leave a Reply